Fanuc ic695psd040 DC Power Supply 40W
ic695psd040 GE Fanuc DC Power Supply 40W
ic695psd040 GE Fanuc DC Power Supply 40W | Power Supply GE Fanuc IC695PSD040 is a 40-Watt supply that operates
from an input voltage source in the range of 18 VDC to 30 VDC.
This power supply provides three outputs:
▪ +5.1 VDC output.
▪ +24 VDC relay output that can be used to power circuits on Output Relay modules.
▪ +3.3 VDC. This output is used internally by RX3i modules with IC695 catalog numbers.
Caution
Only one GE Fanuc Power Supply IC695PSD040 can be installed in a PACsystems RX3i (IC695 catalog number) Universal Backplane.
This Power supply cannot be used with other RX3i power supplies in redundant or increased capacity modes.
GE Fanuc Power Supply version IC695PSD040C or before may cause equipment damage if inadvertently installed in the same backplane as another RX3i power supply.
This DC Power Supply occupies one backplane slot. If the number of modules required exceeds the capacity of the Power Supply, the additional modules must be installed in Expansion or Remote backplanes or power supplies capable of increased capacity mode operation must be used.
The Power Supply indicates when an internal fault occurs so the CPU can detect loss of power or log the appropriate fault code
GE Fanuc ic695psd040 DC Power Supply Specifications:
| Nominal Rated Voltage | 24 VDC |
| Input Voltage Range | 18 to 30 VDC |
| Input Power | 60 Watts maximum at full load |
| Inrush Current | 4 Amps, 100 milliseconds maximum * |
GE Fanuc ic695psd040Output Power |
40 Watts maximum total of both outputs.
5.1 VDC = 30 Watts maximum 3.3 VDC = 30 Watts maximum Maximum output power depends on ambient temperature, as shown. |
GE Fanuc ic695psd040Output Voltage |
5.1 VDC: 5.0 VDC to 5.25 VDC (5.1 VDC nominal)
3.3 VDC: 3.2 VDC to 3.465 VDC (3.3 VDC nominal) |
GE Fanuc ic695psd040Output Current |
5.1 VDC: 0 to 6 Amps
3.3 VDC: 0 to 9 Amps |
| Isolation | None |
| Ripple (all outputs) | 50 mV |
| Noise (all outputs) | 50 mV |
| Ride-through time | 10 ms This is the length of time the Power Supply maintains valid outputs if the power source is interrupted.
If this Power Supply is used with IC694 and IC693 modules that have relay outputs, special precautions should be taken because dropouts in the source voltage will be seen by the module and may cause relay dropouts. |
| Wiring Terminals | Each terminal accepts one 14 AWG to 22 AWG wire. |
| Terminal Current | 6 Amps |
| Number of Daisy-Chained PSD040 Supplies | Up to 2 |
| Installation Environment | For use in Pollution Degree 2 environments only |
GE Fanuc ic695psd040 and Other type :
IC200MDD844 | GE Fanuc | Positive Logic VersaMax Discrete Mixed Module
IC200ALG230 | GE Fanuc | VersaMax Analog Input Module
IC694CHS392 | GE Fanuc | RX3i Baseplate Expansion
IC693CHS392 | GE Fanuc | 10 Slot Expansion Baseplate
IC694MDL660 | GE Fanuc | 24 VDC 32-Point Positive/Negative Logic Input Module
IC200UEX636 | GE Fanuc | Analog Expansion Units
IC200UDR005 | GE Fanuc | 28 Point Micro PLC
IC694MDL754 | GE Fanuc | Output Module, 12/24VDC, 0.75A, 32-Point Grouped, with ESCP
IC200PBI001 | GE Fanuc | VersaMax Profibus Network Interface Module
IC200ALG260 | GE Fanuc | VersaMax Analog Input Module
IC695PSD140 | GE Fanuc | Multipurpose Power Supply
IC200ALG620 | GE Fanuc | VersaMax Analog Input Module
IC200ALG331 | GE Fanuc | Analog Output Module
GE Fanuc ic695psd040 and Other type :
IC200GBI001 | GE Fanuc | Genius Network Interface Unit
IC695PSA140 | GE Fanuc | PACSystems™ RX3i Universal Power Supply
IC200ALG262 | GE Fanuc | VersaMax Analog Input Module
IC693PWR322 | GE Fanuc | PLC Series 90-30 Standard DC Power Supply
IC200ALG264 | GE Fanuc | Analog Input Module
IC693ALG223 | GE Fanuc | Analog Current Input – 16 Channel Module
IC200ALG326 | GE Fanuc | Analog Output Modules
IC693PWR331 | GE Fanuc | High Capacity Power Supply
GE Fanuc ic695psd040 and other type :
IC694ALG223 | GE Fanuc | 16–Channel Analog Current Input Module
IC200ALG240 | GE Fanuc | VersaMax Analog Input Module
IC200ALG328 | GE Fanuc | VersaMax Analog Output Module
IC695ETM001 | GE Fanuc | Ethernet Interface Module
IC694ALG392 | GE Fanuc | RX3i 8-Channel Analog Current/Voltage Output Module
IC695PBM300 | GE Fanuc | PROFIBUS Master Module
IC695NIU001 | GE Fanuc | Ethernet Network Interface Unit
IC695RMX128 | GE Fanuc | RX3i Redundancy Memory Xchange (RMX) Module
IC693CMM321 | GE Fanuc | Ethernet Interface TCP/IP Module
IC695CPE305 | GE Fanuc | RX3i Central Processing Unit CPU
IC695CPU310 | GE Fanuc | RX3i VME 300 Mhz CPU
IC695CPE310 | GE Fanuc | Central Processing Unit
GE Fanuc ic695psd040 and Other type :
IC697PWR711 | GE Fanuc | Power Supply Module
IC693CPU372 | GE Fanuc | CPU Module
IC200UDD110 | GE Fanuc | 28-Point Micro PLC Power Supply
IC200UDR010 | GE Fanuc | 28-Point Micro PLC Power Supply
IC200UEX214 | GE Fanuc | 28 Point Micro PLC Expansion Unit
IC200UEX626 | GE Fanuc | 6 Point Analog Expansion Unit
IC693CMM302 | GE Fanuc | Enhanced Genius Communications Module
IC694MDL742 | GE Fanuc | MDL742 Output Module
IC200PNS001 | GE Fanuc | Remote I/O PROFINET Network Interface Unit
IC200MDL650 | GE Fanuc | VersaMax Discrete Input Module
IC200MDL750 | GE Fanuc | Positive Logic Output Module
IC200MDL930 | GE Fanuc Relay Output Module
IC200MDL331 | GE Fanuc | VersaMax Discete Output
IC200UEM001 | GE Fanuc Ethernet Communications Module
IC200ALG320 | GE Fanuc | Analog Output Module
IC200MDL940 | GE Fanuc | VersaMax Discrete Output Module
IC200MDL742 | GE Fanuc | VersaMax Discrete Output Module
IC200MDL243 | GE Fanuc | Discrete Input Modules
IC695ALG312 | GE Fanuc | Isolated Thermocouple Input module 6 Channels
IC200MDL240 | GE Fanuc | Discrete Input Modules
IC697ALG230 | GE Fanuc Analog Input Module
A06B-6151-H030 | GE Fanuc | Alpha i Spindle Module AiSP-30HV
GE Fanuc ic695psd040 and other type :
IC694MDL330 | GE Fanuc | PACSystems RX3i AC Voltage Input Module
IC694MDL758 | GE Fanuc | Output Module 12/24Vdc
IC695ALG608 | GE Fanuc Analog Input Module
IC697PWR713 | GE Fanuc | AD/DC Power Supply
IC200MDL | GE Fanuc | Input Modules